收藏本站
MB85RC16V
? Current Address Read
If the last write or read operation finishes correctly up to the end of stop condition, the memory address that
was accessed last remains in the memory address buffer (the length is 11 bits).
When sending this command without turning the power off, it is possible to read from the memory address
n+1 which adds 1 to the total 11-bit memory address n, which consists of the memory upper address 3-bit
from the device address word input and the lower 8-bit of the memory address buffer. If the memory address
n is the last address, it is possible to read with rolling over to the head of the memory address (000 H ). The
current address (address that the memory address buffer indicates) is undefined immediately after turning
the power on.
Access from master
Access from slave
(n+1) memory address
S Start Condition
S
1 0 1 0 A2 A1 A0 1 A
Read
Data 8b its
N P
P Stop Condition
A ACK (SDA is the "L"le v el)
N N ACK (SDA is the "H" le v el)
? Random Read
After specifying the address as well as for write system command, issuing another start condition, by trans-
mitting Device Address Word (R/W “1” input), the one byte data from the memory address saved in the
memory address buffer can be read synchronously to SCL.
Setting values for the first and the second memory upper address codes should be the same (The figure
below shows the input example).
The final NACK (SDA is the “H” level) is issued by the receiver that receives the data. In this case, this bit is
issued by the master side.
n address
S
1 0 1 0 A2 A1 A0 0 A
Address
Lo w 8b its
A S
1 0 1 0 A2 A1 A0 1 A
Read
Data 8b its
N P
(Input example) when reading
memory address 16F H :
001 B
01101111 B
001 B
Access from master
Access from slave
S Start Condition
P Stop Condition
A ACK (SDA is the "L" le v el)
N N ACK (SDA is the "H" le v el)
10
DS501-00010-2v0-E
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MB85RC64PNF-G-JNE1 IC FRAM 64KBIT 400KHZ 8SOP
MB85RS128APNF-G-JNE1 IC FRAM 128KBIT 25MHZ 8SOP
MB85RS64PNF-G-JNE1 IC FRAM 64KBIT 20MHZ 8SOP
MC10SX1130DR2 IC LED DRIVER LINEAR 16-SOIC
MC33152DG IC DRIVER MOSFET DUAL HS 8SOIC
MC33153PG IC DRIVER GATE SINGLE IGBT 8DIP
MC34151DG IC MOSFET DRIVER DUAL HS 8SOIC
MC34844EP IC LED DVR BACKLIGHT 10CH 32QFN
相关代理商/技术参数
MB85RC16VPNF-G-JNERE1 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:16K(2K8) bit,I2C,Memory FRAM
MB85RC16VPNF-G-JNN1E1 制造商:FUJITSU 功能描述:
MB85RC16VPNF-G-JNN1ERE1 制造商:FUJITSU 功能描述:
MB85RC1MTPNF-G-JNERE1 功能描述:IC FRAM 1MBIT 3.4MHZ 8SOP 制造商:fujitsu electronics america, inc. 系列:- 包装:剪切带（CT） 零件状态:有效 格式 - 存储器:RAM 存储器类型:FRAM（Ferroelectric RAM） 存储容量:1M（128K x 8） 速度:3.4MHz 接口:I2C，2 线串口 电压 - 电源:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TA） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOP 标准包装:1
MB85RC256V 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:256 K (32 K??8) ?????????I2C
MB85RC256VPF-G-JNERE2 制造商:FUJITSU 功能描述:IC FRAM 256KBIT 1MHZ 8SOP 制造商:FUJITSU 功能描述:I2C,256K FRAM 制造商:FUJITSU 功能描述:"MB85RC256VPF-G-JNERE2"256KI2CFRAM 制造商:FUJITSU 功能描述:"MB85RC256VPF-G-JNERE2"256KI2C serialFRAM 制造商:FUJITSU 功能描述:256KBit I2C FRAM
MB85RC256VPNF-ES-JNE1 制造商:FUJITSU 功能描述:
MB85RC256VPNF-G-JNE1 制造商:FUJITSU 功能描述: